ISO 10467-2018 PDF

Full title and description

ISO 10467:2018 — Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass‑reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin. This edition specifies the properties, dimensional and performance requirements and relevant test parameters for GRP (UP) pipes, fittings and joints intended primarily for buried drainage and sewerage installations (nominal sizes DN 50 to DN 4000).

Abstract

This standard defines requirements for GRP piping systems based on unsaturated polyester (UP) resin (vinyl‑ester included by note) used for drainage and sewerage with or without pressure. It covers material and structural characteristics of pipes and fittings, joint types and type‑test performance requirements, and test parameters for proving compliance. The document also references hydrostatic design principles consistent with related ISO technical documents and structural reliability standards.

General information

• Status: Withdrawn (withdrawal action recorded; a newer standard supersedes this edition).
• Publication date: June 2018.
• Publisher: International Organization for Standardization (ISO).
• ICS / categories: 93.030 (External sewage systems); 23.040.20 (Plastics pipes); 91.140.80 (Drainage systems).
• Edition / version: Edition 2 (2018-06).
• Number of pages: 59.

Scope

Applies to GRP piping systems manufactured from unsaturated polyester (UP) resin (note: vinyl‑ester resins are treated as UP for this standard) intended for conveyance of surface water and sewage at temperatures up to 50 °C, with or without pressure, primarily for direct buried installations. The standard addresses pipes, fittings and joints (flexible or rigid, with or without end‑thrust load‑bearing capability) in nominal sizes DN 50 to DN 4000 and includes provisions for non‑buried use when environmental and support conditions are accounted for.

Key topics and requirements

• Material and structural characteristics for GRP (UP) pipes, including options with aggregates, fillers or liners (thermoplastic or thermosetting).
• Dimensional and performance requirements for fittings (bends, branches, reducers, saddles, flanged adaptors) and requirements to prove structural design.
• Requirements and type‑test performance criteria for joints: socket‑and‑spigot (including double‑socket), locked socket, cemented/wrapped joints and bolted flange joints, as a function of declared nominal pressure rating.
• Specified manufacturing techniques for fittings (filament winding, tape winding, contact moulding, hot/cold compression moulding) and corresponding test parameters.
• Hydrostatic pressure design and reliability principles aligned with referenced ISO/TS and structural reliability standards.

Typical use and users

Used by designers, specifiers, manufacturers and testing laboratories in the water, wastewater and civil infrastructure sectors. Typical users include municipal and industrial pipeline engineers, trenchless rehabilitation contractors (e.g., slip‑lining), utility asset owners and conformity assessment bodies responsible for product type testing and system acceptance.

Related standards

ISO 10467:2018 has been withdrawn and superseded by a later ISO publication (ISO 23856:2021). The document also cross‑references related technical publications and design standards used for hydrostatic design and structural reliability (for example ISO/TS 20656‑1, ISO 25780, ISO 2394 and EN 1990 in the context of design principles).

Keywords

GRP, UP resin, vinyl‑ester, plastics piping systems, drainage, sewerage, buried pipes, fittings, joints, DN 50–DN 4000, hydrostatic design, type testing.

FAQ

Q: What is this standard?

A: ISO 10467:2018 is an international standard that specified requirements and test parameters for glass‑reinforced thermosetting plastics (GRP) piping systems based on unsaturated polyester (UP) resin used in drainage and sewerage applications.

Q: What does it cover?

A: It covers material properties, dimensional and performance requirements for pipes and fittings, joint types and their type‑test performance as well as test parameters and manufacturing techniques relevant to GRP (UP) systems intended for buried and certain non‑buried installations.

Q: Who typically uses it?

A: Engineers, designers, manufacturers of GRP pipes and fittings, testing laboratories, utility owners, infrastructure contractors and standards/quality managers specifying or verifying drainage and sewerage pipeline products.

Q: Is it current or superseded?

A: ISO 10467:2018 has been withdrawn; it was superseded by a newer ISO standard published in 2021 (ISO 23856:2021). For current requirements and purchasing, refer to the successor standard.

Q: Is it part of a series?

A: It is part of the body of ISO standards covering plastics piping and drainage systems and is related to other ISO documents addressing GRP pipe testing, hydrostatic design and structural reliability; specific related documents include ISO/TS 20656‑1 and ISO 25780 among others.

Q: What are the key keywords?

A: GRP, unsaturated polyester (UP), vinyl‑ester, drainage, sewerage, plastics piping, fittings, joints, type testing, buried pipelines.