ISO 10630:1994 PDF

Industrial plate screens — Specifications and test methods

Название (английский):

ISO 10630:1994

Industrial plate screens — Specifications and test methods

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 9
Дата публикации:: 28 июля 1994 г.
Издание:: ISO IS 10630 edition 1 version 1
ICS:: 73.120

Тип поставки:

Full version135 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:2 раб. дн. (перевод)

Цена:135 €

Описание (английский):

Specifies technical requirements and test methods for perforated metal plate used for industrial screening purposes and supplied in flat or coiled form. Applies to perforated plates of low carbon steel according to ISO 7805-1 and ISO 7805-2 with nominal sizes of holes from 1 mm for round holes and 4 mm for square holes up to 125 mm according to ISO 2194, and with a maximum plate thickness of 12,5 mm.

Технические детали

Технический комитет: ISO/TC 24/SC 8 - Test sieves, sieving and industrial screens
SKU: ISO 10630:1994

Abstract

Overview

ISO 10630:1994 - "Industrial plate screens - Specifications and test methods" defines technical requirements and test procedures for perforated metal plate used in industrial screening. The standard applies to perforated plates made of low-carbon steel (as referenced to ISO 7805‑1 and ISO 7805‑2), supplied flat or in coils, with nominal hole sizes from 1 mm (round) and 4 mm (square) up to 125 mm (per ISO 2194) and a maximum plate thickness of 12.5 mm. ISO 10630 provides definitions, dimensional tolerances, inspection methods and acceptance criteria to ensure consistent screening performance and interchangeability.

Key topics and requirements

Scope & definitions: clear terms for plate, sheet, coil, perforated plate, pitch, bridge width (bar), margins, and percentage open area.
Material and sizes: low-carbon steel plates, hole size ranges, and maximum thickness (12.5 mm).
Dimensional tolerances: requirements for hole size, pitch and plate dimensions - hole and pitch measurement procedures refer to ISO 7805‑1/2 depending on thickness.
Geometric controls: squareness (amount out‑of‑square), plate width/length, margin widths and acceptable deviations.
Flatness and edge geometry: measurement methods on a reference surface, roller-levelling considerations, and limits for edge bow and wavy edges (to be agreed when outside standard limits).
Surface defects and irregularities: rules and test methods for breakaway zones, burr heights and shearing burrs. (Example: maximum permissible burr heights are specified by plate thickness in the standard.)
Coiled plate provisions: special conditions for coils (limited to thickness

Overview

Key topics and requirements

Scope & definitions: clear terms for plate, sheet, coil, perforated plate, pitch, bridge width (bar), margins, and percentage open area.
Material and sizes: low-carbon steel plates, hole size ranges, and maximum thickness (12.5 mm).
Dimensional tolerances: requirements for hole size, pitch and plate dimensions - hole and pitch measurement procedures refer to ISO 7805‑1/2 depending on thickness.
Geometric controls: squareness (amount out‑of‑square), plate width/length, margin widths and acceptable deviations.
Flatness and edge geometry: measurement methods on a reference surface, roller-levelling considerations, and limits for edge bow and wavy edges (to be agreed when outside standard limits).
Surface defects and irregularities: rules and test methods for breakaway zones, burr heights and shearing burrs. (Example: maximum permissible burr heights are specified by plate thickness in the standard.)
Coiled plate provisions: special conditions for coils (limited to thickness

ISO 10630:1994 PDF

Технические детали

Abstract

Overview

Key topics and requirements

Похожие стандарты

Abstract

Overview

Key topics and requirements

Похожие стандарты

Industrial plate screens -- Part 1: Thickness of 3 mm and above

Industrial plate screens -- Part 2: Thickness below 3 mm

Mechanical vibration. Rotor balancing. Susceptibility and sensitivity of machines to unbalance.

Industrial plate screens - Specifications and test methods