ISO 16276-1:2007 PDF

Corrosion protection of steel structures by protective paint systems — Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating — Part 1: Pull-off testing

Название (английский):

ISO 16276-1:2007

Статус документа:: Отменён
Формат:: Электронный (PDF)
Количество страниц:: 9
Дата публикации:: 18 мая 2007 г.
Издание:: ISO IS 16276 edition 1 version 1
ICS:: 87.020

Тип поставки:

Full version135 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:2 раб. дн. (перевод)

Цена:135 €

Описание (английский):

ISO 16276-1:2007 specifies procedures for assessing the fracture strength of a protective paint coating of any thickness on a steel substrate of thickness not less than 10 mm. The procedures given in this part of ISO 16276 are based on methods used with different types of pull-off test equipment. The results obtained using such different types of equipment are not comparable. This part of ISO 16276 also specifies suitable equipment and defines inspection areas, sampling plans and acceptance/rejection criteria. It does not give any values of the fracture strength of different protective paint coatings.

Технические детали

Технический комитет: ISO/TC 35/SC 14 - Protective paint systems for steel structures
SKU: ISO 16276-1:2007

Abstract

Overview

ISO 16276-1:2007 defines a standardized procedure for assessing the fracture strength (adhesion/cohesion) of protective paint coatings on steel structures using pull-off testing. Intended for coatings on steel substrates of at least 10 mm thickness, this part specifies suitable equipment, inspection areas, sampling plans and acceptance/rejection criteria, but does not provide numeric fracture-strength values. The standard emphasizes that results from different pull-off devices are not directly comparable, so the test equipment and manufacturer should be specified in contract documentation.

Keywords: ISO 16276-1, pull-off testing, fracture strength, adhesion, cohesion, protective paint systems, steel structures, acceptance criteria

Key topics and technical requirements

Scope: Assessment of fracture strength for coatings of any thickness on steel ≥ 10 mm; test-panels or sandwich techniques referenced for thinner substrates.
Terminology: Introduces “fracture strength” to cover both adhesion (coat–substrate) and cohesion (within a coat).
Test principle: Fix test cylinders (dollies) to the coating with adhesive, apply perpendicular tensile force until fracture; measure the force.
Apparatus & consumables:
- Tensile/pull-off apparatus (manufacturer and model must be agreed/specifed).
- Dollies (typically ~20 mm diameter; stainless steel or aluminium; length ≥ half diameter).
- Adhesives suitable for the coating (e.g., 2-pack epoxy, 1-pack cyanoacrylate).
- Circular cutting device for isolating the test area.
Procedural controls:
- Calibration of measurement equipment is required.
- Force must be applied uniformly, ≤ 1 MPa/s, with fracture occurring within 90 s.
- Coating cure: follow manufacturer; otherwise dry/cure ≥ 10 days at substrate temperature >15 °C and RH

Overview

Keywords: ISO 16276-1, pull-off testing, fracture strength, adhesion, cohesion, protective paint systems, steel structures, acceptance criteria

Key topics and technical requirements

Scope: Assessment of fracture strength for coatings of any thickness on steel ≥ 10 mm; test-panels or sandwich techniques referenced for thinner substrates.
Terminology: Introduces “fracture strength” to cover both adhesion (coat–substrate) and cohesion (within a coat).
Test principle: Fix test cylinders (dollies) to the coating with adhesive, apply perpendicular tensile force until fracture; measure the force.
Apparatus & consumables:
- Tensile/pull-off apparatus (manufacturer and model must be agreed/specifed).
- Dollies (typically ~20 mm diameter; stainless steel or aluminium; length ≥ half diameter).
- Adhesives suitable for the coating (e.g., 2-pack epoxy, 1-pack cyanoacrylate).
- Circular cutting device for isolating the test area.
Procedural controls:
- Calibration of measurement equipment is required.
- Force must be applied uniformly, ≤ 1 MPa/s, with fracture occurring within 90 s.
- Coating cure: follow manufacturer; otherwise dry/cure ≥ 10 days at substrate temperature >15 °C and RH

ISO 16276-1:2007 PDF

Технические детали

Abstract

Overview

Key topics and technical requirements

Похожие стандарты

Abstract

Overview

Key topics and technical requirements

Похожие стандарты

Corrosion protection of steel structures by protective paint systems. Assessment of, and acceptance criteria…

Water quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…

Standard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)

Standard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)

Standard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…

Standard Practice for Dosimetry in Radiation Processing

Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies

Additive Manufacturing — Round Robin Testing — General Guidelines