ISO 21635:2018 PDF

Ships and marine technology — Specification of high manganese austenitic steel used for LNG tanks on board ships

Название (английский):

ISO 21635:2018

Ships and marine technology — Specification of high manganese austenitic steel used for LNG tanks on board ships

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 6
Дата публикации:: 17 июля 2018 г.
Издание:: ISO IS 21635 edition 1 version 1
ICS:: 47.020.05

Тип поставки:

Full version90 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:1 раб. дн. (перевод)

Цена:90 €

Описание (английский):

This document describes the specification of high manganese (Mn) austenitic steel plates to be used for LNG tanks on board ships. The specification of high manganese austenitic steel can be also considered for design and manufacture of cargo tanks and process pressure vessels of LNG supply/terminal and transportation of fuels and traded gases. This document is primarily applicable for the specification of LNG tanks below volumetric capacity of approximately 30 000 m3 using high manganese austenitic steel. The thickness of plates is limited to between 6 mm to 40 mm.

Технические детали

Технический комитет: ISO/TC 8/SC 8 - Ship design
SKU: ISO 21635:2018

Abstract

Overview

ISO 21635:2018 specifies requirements for high manganese (Mn) austenitic steel plates intended for LNG tanks on board ships. The standard targets plates with thicknesses between 6 mm and 40 mm and is primarily applicable to LNG tanks with volumetric capacity up to approximately 30 000 m3. It provides material purchasers, shipyards, steelmakers and tank manufacturers with requirements covering chemical composition, mechanical properties, manufacture, testing and documentation.

Key Topics

Chemical composition: The standard defines a high Mn chemistry to retain austenite as the primary phase (Mn typically in the range indicated by the standard). Other alloying and impurity elements are controlled per the specification.
Mechanical properties: Tensile and yield strength, elongation and Charpy V-notch impact energy requirements are specified. Impact testing is required at cryogenic temperatures (default test temperature -196 °C) with minimum average absorbed energies stated for transverse and longitudinal specimens.
Manufacture and processing: Plates must be produced by recognized steelmaking routes, be killed, hot-rolled and subject to controlled cooling to avoid grain boundary carbide precipitation. A recommended cooling rate faster than 10 °C/s is given and forming above 500 °C is not permitted.
Testing and acceptance: Tensile tests (ISO 6892-1) and Charpy V-notch tests (ISO 148-1) are required from each piece. Sub-sized specimens are permitted for thin plates (t

Overview

Key Topics

Chemical composition: The standard defines a high Mn chemistry to retain austenite as the primary phase (Mn typically in the range indicated by the standard). Other alloying and impurity elements are controlled per the specification.
Mechanical properties: Tensile and yield strength, elongation and Charpy V-notch impact energy requirements are specified. Impact testing is required at cryogenic temperatures (default test temperature -196 °C) with minimum average absorbed energies stated for transverse and longitudinal specimens.
Manufacture and processing: Plates must be produced by recognized steelmaking routes, be killed, hot-rolled and subject to controlled cooling to avoid grain boundary carbide precipitation. A recommended cooling rate faster than 10 °C/s is given and forming above 500 °C is not permitted.
Testing and acceptance: Tensile tests (ISO 6892-1) and Charpy V-notch tests (ISO 148-1) are required from each piece. Sub-sized specimens are permitted for thin plates (t

ISO 21635:2018 PDF

Технические детали

Abstract

Overview

Key Topics

Похожие стандарты

Abstract

Overview

Key Topics

Похожие стандарты

Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2019)

Intelligent transport systems. Traffic and travel information messages via traffic message coding. Coding pro…

Water quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…

Standard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)

Standard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)

Standard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…

Standard Practice for Dosimetry in Radiation Processing

Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies