ISO 25358:2018 PDF

Crop protection equipment — Droplet-size spectra from atomizers — Measurement and classification

Название (английский):

ISO 25358:2018

Crop protection equipment — Droplet-size spectra from atomizers — Measurement and classification

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 7
Дата публикации:: 10 июля 2018 г.
Издание:: ISO IS 25358 edition 1 version 1
ICS:: 65.060.40

Тип поставки:

Full version105 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:2 раб. дн. (перевод)

Цена:105 €

Описание (английский):

This document specifies procedures for classifying droplet size spectra from atomizers used in spraying for crop protection. It provides a reference system for defining classes of droplet size spectra. Depending on their function principle and individual setup, measuring systems for droplet sizing can give different results. This document provides a means of comparing measured droplet size spectra to reference spectra and enables relative comparisons of droplet size spectra obtained from different measuring systems.

Технические детали

Технический комитет: ISO/TC 23/SC 6 - Equipment for crop protection
SKU: ISO 25358:2018

Abstract

Overview

ISO 25358:2018 - "Crop protection equipment - Droplet-size spectra from atomizers - Measurement and classification" specifies procedures for measuring and classifying droplet-size spectra produced by atomizers used in crop protection spraying. The standard provides a reference system of reference droplet size spectra (reference sprays and nozzle/pressure combinations) to enable relative comparison of results obtained from different measuring systems and laboratories.

Key topics and technical requirements

Scope: Classification of droplet size spectra using reference spectra; intended to harmonize terminology and relative comparisons across instruments.
Reference spectra and nozzles: Defines boundary spectra using specified reference nozzle/flow rate (pressure) combinations (see Table 1 in the standard - e.g., Mee Fog IP‑16 and various TeeJet models).
Measurement parameters reported: Characteristic diameters Dv0.1, Dv0.5 (volume median diameter), and Dv0.9 (10%, 50%, 90% cumulative volume points).
Sampling and measurement:
- Use at least three candidate atomizers from a batch of ≥10 with flow deviation ±3% of manufacturer rating.
- Representative cross‑sectional sampling of the spray plume at typically 30–50 cm from nozzle (or appropriate distance for full atomization).
- Recommended environmental conditions for inter‑laboratory comparison: spray liquid and air at (20 ± 2) °C, relative humidity 40–80%.
Instruments: Accepts non‑intrusive methods appropriate for the droplet size range and liquid (e.g., phase Doppler, laser diffraction, imaging, single‑particle counters). Instrument configuration and calibration must be verified.
Precision and calibration:
- Repeatability targets (example): maximum deviations between replicates for Dv0.5 of ±10%; laser diffraction replicates often required

Overview

Key topics and technical requirements

Scope: Classification of droplet size spectra using reference spectra; intended to harmonize terminology and relative comparisons across instruments.
Reference spectra and nozzles: Defines boundary spectra using specified reference nozzle/flow rate (pressure) combinations (see Table 1 in the standard - e.g., Mee Fog IP‑16 and various TeeJet models).
Measurement parameters reported: Characteristic diameters Dv0.1, Dv0.5 (volume median diameter), and Dv0.9 (10%, 50%, 90% cumulative volume points).
Sampling and measurement:
- Use at least three candidate atomizers from a batch of ≥10 with flow deviation ±3% of manufacturer rating.
- Representative cross‑sectional sampling of the spray plume at typically 30–50 cm from nozzle (or appropriate distance for full atomization).
- Recommended environmental conditions for inter‑laboratory comparison: spray liquid and air at (20 ± 2) °C, relative humidity 40–80%.
Instruments: Accepts non‑intrusive methods appropriate for the droplet size range and liquid (e.g., phase Doppler, laser diffraction, imaging, single‑particle counters). Instrument configuration and calibration must be verified.
Precision and calibration:
- Repeatability targets (example): maximum deviations between replicates for Dv0.5 of ±10%; laser diffraction replicates often required

ISO 25358:2018 PDF

Технические детали

Abstract

Overview

Key topics and technical requirements

Похожие стандарты

Abstract

Overview

Key topics and technical requirements

Похожие стандарты

Water quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…

Standard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)

Standard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)

Standard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…

Standard Practice for Dosimetry in Radiation Processing

Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies

Additive Manufacturing — Round Robin Testing — General Guidelines

Standard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts