ISO 6363-5:2022 PDF

Wrought aluminium and aluminium alloys — Cold-drawn rods/bars, tubes and wires — Part 5: Tolerances on form and dimensions for drawn square and hexagonal bars and wires

Название (английский):

ISO 6363-5:2022

Wrought aluminium and aluminium alloys — Cold-drawn rods/bars, tubes and wires — Part 5: Tolerances on form and dimensions for drawn square and hexagonal bars and wires

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 5
Дата публикации:: 1 июля 2022 г.
Издание:: ISO IS 6363 edition 3 version 1
ICS:: 77.150.10

Тип поставки:

Full version75 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:1 раб. дн. (перевод)

Цена:75 €

Описание (английский):

This document specifies the tolerances on form and dimensions of wrought aluminium and aluminium alloy drawn square and hexagonal bars and wires with widths across flats up to and including 100 mm. For wires, this document does not apply to electrical, welding and aeronautical purposes. For drawn bars, 4.1 to 4.5 apply, and only 4.1 applies to drawn wires.

Технические детали

Технический комитет: ISO/TC 79/SC 6 - Wrought aluminium and aluminium alloys
SKU: ISO 6363-5:2022

Abstract

Overview

ISO 6363-5:2022 defines the tolerances on form and dimensions for cold-drawn wrought aluminium and aluminium-alloy square and hexagonal bars and wires with widths across flats up to and including 100 mm. The third edition (2022) updates and corrects the previous edition (2012). For drawn bars, sections 4.1–4.5 apply; for drawn wires, only section 4.1 (width across flats tolerances) applies. This part of the ISO 6363 series is intended for manufacturers, purchasers and inspection bodies specifying and verifying dimensional and form tolerances for drawn aluminium products. Note: the standard does not apply to wires for electrical, welding or aeronautical purposes.

Key topics and technical requirements

Scope limit: widths across flats ≤ 100 mm; wires for certain critical applications excluded.
Tolerances on width across flats (4.1): plus-and-minus or minus-only tolerances provided in tabulated form (Table 1); choice agreed between purchaser and supplier.
Fixed-length tolerances (4.2): length tolerance bands for fixed-length bars by length ranges (Table 2).
Squareness of cut ends (4.3): limited to half the fixed-length tolerance range (applies to both fixed and random lengths).
Corner radii (4.4): maximum corner radii defined by width ranges (Table 3) - corners shall be slightly rounded but not exceed the stated maxima.
Form tolerances (4.5) (bars only, except certain tempers):
- Measurement method: place bar on a horizontal plate under its own mass.
- Straightness: maximum 2 mm per 1 000 mm of length (total) and ≤ 0.6 mm per 300 mm section.
- Convexity/concavity: controlled within width-across-flats tolerances.
- Twist: limits per 1 000 mm and over total length (Table 4) with different limits for s ≤ 50 mm and 50

Overview

Key topics and technical requirements

Scope limit: widths across flats ≤ 100 mm; wires for certain critical applications excluded.
Tolerances on width across flats (4.1): plus-and-minus or minus-only tolerances provided in tabulated form (Table 1); choice agreed between purchaser and supplier.
Fixed-length tolerances (4.2): length tolerance bands for fixed-length bars by length ranges (Table 2).
Squareness of cut ends (4.3): limited to half the fixed-length tolerance range (applies to both fixed and random lengths).
Corner radii (4.4): maximum corner radii defined by width ranges (Table 3) - corners shall be slightly rounded but not exceed the stated maxima.
Form tolerances (4.5) (bars only, except certain tempers):
- Measurement method: place bar on a horizontal plate under its own mass.
- Straightness: maximum 2 mm per 1 000 mm of length (total) and ≤ 0.6 mm per 300 mm section.
- Convexity/concavity: controlled within width-across-flats tolerances.
- Twist: limits per 1 000 mm and over total length (Table 4) with different limits for s ≤ 50 mm and 50

ISO 6363-5:2022 PDF

Технические детали

Abstract

Overview

Key topics and technical requirements

Похожие стандарты

Abstract

Overview

Key topics and technical requirements

Похожие стандарты

Wrought aluminium and aluminium alloy cold-drawn rods/bars and tubes — Part 2: Mechanical properties

Water quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…

Standard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)

Standard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)

Standard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…

Standard Practice for Dosimetry in Radiation Processing

Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies

Additive Manufacturing — Round Robin Testing — General Guidelines