ISO 6788:1997 PDF

Assembly tools for screws and nuts — Four-way socket wrenches — Dimensions and torque test

Название (английский):

ISO 6788:1997

Assembly tools for screws and nuts — Four-way socket wrenches — Dimensions and torque test

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 4
Дата публикации:: 18 декабря 1997 г.
Издание:: ISO IS 6788 edition 2 version 1
ICS:: 25.140.30

Тип поставки:

Full version60 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:1 раб. дн. (перевод)

Цена:60 €

Описание (английский):

La présente Norme internationale prescrit les dimensions d'encombrement, têtes et bras, en millimètres, des clés en croix types 1, 2, 3 et 4, et spécifie les conditions d'essai en vue de vérifier l'aptitude de l'outil à sa fonction. Elle est applicable aux clés en croix pour la manoeuvre des boulonneries à surplats de dimensions métriques des camions et automobiles. Ces clés figurent sous le numéro 21 de l'ISO 1703.

Технические детали

Технический комитет: ISO/TC 29/SC 10 - Assembly tools for screws and nuts, pliers and nippers
SKU: ISO 6788:1997

Abstract

Overview

ISO 6788:1997 specifies dimensional and test requirements for four-way socket wrenches used for assembling screws and nuts on trucks and cars. The second edition (1997) defines socket head dimensions (in millimetres) for four designated wrench types and prescribes a torque test procedure to verify tool performance. The standard targets manufacturers, designers, quality engineers and procurement professionals involved with hand assembly tools.

Key topics and requirements

Dimensions and tolerances
- Socket head dimensions are given in millimetres for four wrench types (illustrated in the standard).
- Tolerances on wrench openings follow ISO 691 ("unmachined closed" series).
- Driving squares must conform to ISO 1174-1.
- Maximum outside head dimensions are specified as 10% greater than values given in ISO 2236.
- Half-arm lengths must be equal within a tolerance of –3% of the nominal length, and the arm angle is 90° – 2°.
Material hardness
- Minimum hardness requirements for sockets and male driving squares reference ISO 1711‑1 and ISO 3316, respectively.
Torque testing
- Torque tests are performed by placing the socket or square drive over the appropriate test mandrel and applying the corresponding torque values referenced in ISO 1711‑1 (for hexagonal sockets) and ISO 3316 (for square drives).
- A support must be used to avoid bending moments caused by the arm length (distance l/2) during the test.
- After testing, the wrench must show no permanent deformation or defects that could affect use.
Designation and marking
- Example designation formats are provided (e.g., Wrench ISO 6788 – 18 × 21 × 22 × 24, or Wrench ISO 6788 – 18 × 21 × 22 × A 12,5).
- Tools must be permanently and legibly marked with at least the width across flats and the manufacturer’s name or trademark.

Applications and users

Practical for tool manufacturers, quality-control labs, and tool designers specifying dimensional and mechanical requirements for four-way socket wrenches.
Used by automotive and truck assembly operations, maintenance workshops, and procurement teams to ensure interchangeability, safety and durability of hand tools.
Useful for standards committees and test houses establishing compliance and product certification.

Related standards

ISO 691:1997 (wrench and socket opening tolerances)
ISO 1174-1:1996 (driving squares for hand socket tools)
ISO 1711-1:1996 (technical specs for hand wrenches and sockets)
ISO 2236:1991 (maximum outside head dimensions)
ISO 3316:1996 (attachments and tests)
ISO 1703 (nomenclature for assembly tools)

Overview

Key topics and requirements

Dimensions and tolerances
- Socket head dimensions are given in millimetres for four wrench types (illustrated in the standard).
- Tolerances on wrench openings follow ISO 691 ("unmachined closed" series).
- Driving squares must conform to ISO 1174-1.
- Maximum outside head dimensions are specified as 10% greater than values given in ISO 2236.
- Half-arm lengths must be equal within a tolerance of –3% of the nominal length, and the arm angle is 90° – 2°.
Material hardness
- Minimum hardness requirements for sockets and male driving squares reference ISO 1711‑1 and ISO 3316, respectively.
Torque testing
- Torque tests are performed by placing the socket or square drive over the appropriate test mandrel and applying the corresponding torque values referenced in ISO 1711‑1 (for hexagonal sockets) and ISO 3316 (for square drives).
- A support must be used to avoid bending moments caused by the arm length (distance l/2) during the test.
- After testing, the wrench must show no permanent deformation or defects that could affect use.
Designation and marking
- Example designation formats are provided (e.g., Wrench ISO 6788 – 18 × 21 × 22 × 24, or Wrench ISO 6788 – 18 × 21 × 22 × A 12,5).
- Tools must be permanently and legibly marked with at least the width across flats and the manufacturer’s name or trademark.

Applications and users

Practical for tool manufacturers, quality-control labs, and tool designers specifying dimensional and mechanical requirements for four-way socket wrenches.
Used by automotive and truck assembly operations, maintenance workshops, and procurement teams to ensure interchangeability, safety and durability of hand tools.
Useful for standards committees and test houses establishing compliance and product certification.

Related standards

ISO 691:1997 (wrench and socket opening tolerances)
ISO 1174-1:1996 (driving squares for hand socket tools)
ISO 1711-1:1996 (technical specs for hand wrenches and sockets)
ISO 2236:1991 (maximum outside head dimensions)
ISO 3316:1996 (attachments and tests)
ISO 1703 (nomenclature for assembly tools)

ISO 6788:1997 PDF

Технические детали

Abstract

Overview

Key topics and requirements

Applications and users

Related standards

Похожие стандарты

Abstract

Overview

Key topics and requirements

Applications and users

Related standards

Похожие стандарты

Assembly tools for screws and nuts — Wrench and socket openings — Tolerances for general use

Assembly tools for screws and nuts — Driving squares — Part 1: Driving squares for hand socket tools

Assembly tools for screws and nuts — Technical specifications — Part 1: Hand-operated wrenches and sockets

Assembly tools for screws and nuts — Forged and tubular socket wrenches — Maximum outside head dimensions

Assembly tools for screws and nuts — Attachments for hand-operated square drive socket wrenches — Dimensions…

Cinematography. 16 mm motion-picture magnetic film. Cutting and perforating dimensions

Assembly tools for screws and nuts. Driving squares. Driving squares for hand socket tools.

Crop protection equipment. Test methods for the evaluation of cleaning systems. Internal cleaning of tank.