ISO 8643:2024 PDF

Earth-moving machinery — Hydraulic excavator and backhoe loader lowering control device — Requirements and tests

Название (английский):

ISO 8643:2024

Earth-moving machinery — Hydraulic excavator and backhoe loader lowering control device — Requirements and tests

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 10
Дата публикации:: 8 мая 2024 г.
Издание:: ISO IS 8643 edition 4 version 1
ICS:: 53.100

Тип поставки:

Full version150 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:2 раб. дн. (перевод)

Цена:150 €

Описание (английский):

This document establishes uniform requirements and test procedures for lowering control devices fitted on the boom, intermediate boom and arm cylinders of hydraulic excavators and backhoe loaders to control the rate of drop in the case of a hydraulic line failure or rupture. It is applicable to the lowering control devices of hydraulic excavators and the backhoe equipment of backhoe loaders used for object handling which are equipped with the standard linkage as defined by the manufacturer. On machines where alternative linkage combinations are offered, only the standard length defined by the manufacturer is subject to testing.

Технические детали

Технический комитет: ISO/TC 127/SC 1 - Test methods relating to safety and machine performance
SKU: ISO 8643:2024

Abstract

Overview

ISO 8643:2024 specifies uniform requirements and test procedures for lowering control devices (also referred to in parts of the standard as lifting linkage control valves) fitted to the boom, intermediate boom and arm cylinders of hydraulic excavators and the backhoe equipment of backhoe loaders. The standard targets machines used for object handling and defines how lowering control devices must behave to control the rate of drop if a hydraulic line fails or ruptures. It applies to machines equipped with the manufacturer’s standard linkage length.

Key topics and requirements

Purpose: ensure controlled lowering of loads in the event of hydraulic line failure to reduce risk to people and machine stability.
Scope: devices fitted on lifting linkage cylinders of excavators and backhoe loaders used for object handling.
Automatic operation: the lowering control device must operate automatically while cylinders are pressurized, even with the machine/ignition switched off (Clause 4.1).
Safety and stability: device operation must not degrade normal machine response or compromise stability (Clause 4.2).
Installation durability: tubes and fittings connecting device and any parallel relief valve must have a minimum burst pressure of four times the working circuit pressure; hoses are not acceptable for those critical connections (Clause 4.5).
Leakage and performance limits:
- Internal leakage test: vertical drop rate ≤ 10 mm/s at 1.0 m test height (Table 1).
- Holding/raising tests: total vertical drop ≤ 100 mm in 10 s.
- Lowering test: increase in lowering speed shall be less than 100% of initial speed averaged over at least 2 s; total vertical drop ≤ 100 mm in 10 s.
- Signal line rupture: oil leakage ≤ 10 L/min per cylinder at 40–50 °C.
- Equalizing lines: for machines ≤ 40 t leakage

Overview

Key topics and requirements

Purpose: ensure controlled lowering of loads in the event of hydraulic line failure to reduce risk to people and machine stability.
Scope: devices fitted on lifting linkage cylinders of excavators and backhoe loaders used for object handling.
Automatic operation: the lowering control device must operate automatically while cylinders are pressurized, even with the machine/ignition switched off (Clause 4.1).
Safety and stability: device operation must not degrade normal machine response or compromise stability (Clause 4.2).
Installation durability: tubes and fittings connecting device and any parallel relief valve must have a minimum burst pressure of four times the working circuit pressure; hoses are not acceptable for those critical connections (Clause 4.5).
Leakage and performance limits:
- Internal leakage test: vertical drop rate ≤ 10 mm/s at 1.0 m test height (Table 1).
- Holding/raising tests: total vertical drop ≤ 100 mm in 10 s.
- Lowering test: increase in lowering speed shall be less than 100% of initial speed averaged over at least 2 s; total vertical drop ≤ 100 mm in 10 s.
- Signal line rupture: oil leakage ≤ 10 L/min per cylinder at 40–50 °C.
- Equalizing lines: for machines ≤ 40 t leakage

ISO 8643:2024 PDF

Технические детали

Abstract

Overview

Key topics and requirements

Похожие стандарты

Abstract

Overview

Key topics and requirements

Похожие стандарты

Water quality — Biological classification of rivers — Part 1: Guidance on the interpretation of biological qu…

Standard Practice for Use of a Radiochromic Liquid Dosimetry System (Withdrawn 2020)

Standard Practice for Dosimetry in Gamma Irradiation Facilities for Food Processing (Withdrawn 2013)

Standard Practice for Dosimetry in Electron Beam and X-Ray (Bremsstrahlung) Irradiation Facilities for Food P…

Standard Practice for Dosimetry in Radiation Processing

Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies

Additive Manufacturing — Round Robin Testing — General Guidelines

Standard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts