ISO 8759-4:2018 PDF

Agricultural tractors — Front-mounted equipment — Part 4: Three-point linkage

Название (английский):

ISO 8759-4:2018

Agricultural tractors — Front-mounted equipment — Part 4: Three-point linkage

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 2
Дата публикации:: 15 ноября 2018 г.
Издание:: ISO IS 8759 edition 1 version 1
ICS:: 65.060.10

Тип поставки:

Full version30 €Read online 24h10 €Read online 72h15 €

Язык документа:

ruen

Срок поставки:1 раб. дн. (перевод)

Цена:30 €

Описание (английский):

This document specifies dimensions and requirements for three-point linkage in association with a power lift for the attachment of implements or equipment to the front of agricultural tractors. It is not applicable to tractors which are designed to run in two directions, where either end can be considered to be the front or the rear. NOTE In this case, ISO 730 applies.

Технические детали

Технический комитет: ISO/TC 23/SC 4 - Tractors
SKU: ISO 8759-4:2018

Abstract

Overview

ISO 8759-4:2018 - "Agricultural tractors - Front-mounted equipment - Part 4: Three-point linkage" is the ISO specification that defines dimensions and requirements for front-mounted three-point linkage systems used with a power lift on agricultural tractors. This first edition (2018) sets geometric and clearance rules to ensure safe, interoperable attachment of front implements and equipment. It does not apply to reversible (bi-directional) tractors - in those cases ISO 730 is the applicable standard.

Key topics and technical requirements

Scope and applicability
- Applies to three-point linkages for front-mounted implements on tractors designed with a distinct front end.
- Excludes tractors designed to run in two directions (ISO 730 applies).
Normative references
- Relies on dimensions and definitions from ISO 730:2009 and ISO 8759-1 (power take-off/safety).
Dimension rules
- Uses ISO 730:2009 (clauses 4.2 and 5.1) as the baseline, with the following exceptions:
  - Upper link point arrangement: must allow a transport pitch of 8° to 12° relative to the vertical mast position.
  - Torsional free float and levelling adjustment: these ISO 730 provisions are not required for front-mounted linkage.
  - Minimum transport heights (by category):
    - Category 1: 700 mm
    - Categories 2N and 2: 850 mm
    - Categories 3N and 3: 900 mm
    - Categories 4N and 4: 1 000 mm
  - Narrow-track / low-clearance tractors: minimum transport height reduced to 375 mm for track settings

Overview

Key topics and technical requirements

Scope and applicability
- Applies to three-point linkages for front-mounted implements on tractors designed with a distinct front end.
- Excludes tractors designed to run in two directions (ISO 730 applies).
Normative references
- Relies on dimensions and definitions from ISO 730:2009 and ISO 8759-1 (power take-off/safety).
Dimension rules
- Uses ISO 730:2009 (clauses 4.2 and 5.1) as the baseline, with the following exceptions:
  - Upper link point arrangement: must allow a transport pitch of 8° to 12° relative to the vertical mast position.
  - Torsional free float and levelling adjustment: these ISO 730 provisions are not required for front-mounted linkage.
  - Minimum transport heights (by category):
    - Category 1: 700 mm
    - Categories 2N and 2: 850 mm
    - Categories 3N and 3: 900 mm
    - Categories 4N and 4: 1 000 mm
  - Narrow-track / low-clearance tractors: minimum transport height reduced to 375 mm for track settings

ISO 8759-4:2018 PDF

Технические детали

Abstract

Overview

Key topics and technical requirements

Похожие стандарты

Abstract

Overview

Key topics and technical requirements

Похожие стандарты

Agricultural wheeled tractors — Rear-mounted three-point linkage — Categories 1N, 1, 2N, 2, 3N, 3, 4N and 4

Simplified method for prediction of the oral bioaccessibility of metals and metalloids in soils

Agricultural tractors - Front-mounted equipment - Part 1: Power take-off: Safety requirements and clearance z…